Click on the image to open
Finished product.
Click on the image to open
20.5 inches deep, 68 inches long, 36 inches tall.
Customer wanted a leg that looked less spindly, and I agreed.
Click on the image to open
Thicker legs with a revised upper portion.
Click on the image to open
8/4 pine was 12 feet long.
I tried to buy 28bf of hard maple, but ended up with 45bf because the widths were all different (my estimates were based on 6 inch widths) and I would rather overbuy than underbuy. But I way overbought.
Click on the image to open
Case construction begins with fitting dados.
Click on the image to open
I used the back panels to hold the sides square as I glued. This worked, but the third panel from the left did not stay seated in the dado fully and I had to re-square it to the rest of the case with a flush trim bit later. That was a pain.
Click on the image to open
1/2 maple ply with butt joints reinforced with 1 inch pocket hole screws. A dado on the bottom received 1/4 maple ply.
Click on the image to open
The legs are 4 pieces of maple glued together. I turned them on a Jet 12-36 lathe that I bought for this project (and many others to come, but I would never pass up the 15% off deal Jet had going at the time) using a set of 6 PSI woodworking turning tools. The setup worked great.
Click on the image to open
I made a story stick out of a scrap of 1/4 inch plywood with diameter dimensions at each of the notches I cut. I made the notches at points of inflection and, for the taper, at the halfway point. I also designed the features of the leg to be nice, even diameters to make my life easy. I used vernier calipers to measure my diameters as I turned.
Click on the image to open
4 legs. Close enough to match. The differences were mainly in the pummels. I have yet to master the skew chisel.
Click on the image to open
Hogged them out on the drill press and cleaned them up with my Narex mortise chisels. I cut the tenons on the tablesaw. With a little setup time, they came out quire accurately.
Click on the image to open
I was happy with where the apron molding met the pummel. I had to make some adjustments on one corner where the pummel did not match exactly, but they were all close.
Click on the image to open
I used a kreg jig and 1 1/4 inch fine thread pocket hole screws to join the face frame. While building the frame, I had to clamp the pieces from all directions down to my table saw to keep the wood from splitting as I drove in the screws. It was a pain.
Click on the image to open
I glued a 1 inch thick piece of hard maple under the face frame and 1/4 inch pieces around the sides to create a sort of waistline that distinguished between the base and the upper case.
Click on the image to open
I started mounting some drawers at this point. The replacement hardware arrived so I was excited to try it out. I love the soft close drawers. I ended up remounting the drawer so it was closer to the front of the case later.
Click on the image to open
You can see the waistline well here. It was needed to visually distinguish top from bottom.
Click on the image to open
I made the shelf by drilling four 1-inch holes in my plywood shelf. Then I applied a 1/2 molding to the shelf to cover the plies. The 1-inch tenons I turned on the legs went through the holes in the shelf and into 1-inch holes in the feet. They have not been glued up yet here.
Click on the image to open
I had intended to have the slides for the shelf mounted on the sides, but the 110º hinges did not allow clearance for that. (Oops.) The instructions for the slides said they work in an undermount position too. I decided to mount them underneath and saw the opportunity for a design change.
Click on the image to open
Here the top is glued up and I am gluing drawer fronts to the drawers. I lined them up based on the door in the middle so they would be even across the top and bottom.
Click on the image to open
Because it was pine, I used Old Master gel stain in American Oak. It was so easy.
Click on the image to open
Test fitting everything before paint.
Click on the image to open
Paint is my least favorite part of the project. I disassembled everything that was not glued on to paint it. I used Benjamin Moore Advance Super White paint. BM Advance is wonderful stuff by the way. I love it.
Click on the image to open
I covered holes that had a tight fit without paint (like the legs holes through the lower shelf) with blue tape to make reassembly easier.
Click on the image to open
Having everything predrilled made this part much, much faster and more fun. I did not end up having to mark and drill finished surfaces.
Click on the image to open
The top got some General Finishes Oil and Poly blend top coat in satin sheen. Wiping is easier than brushing on finish any day.
Click on the image to open
In its final location in the home of the customer. He was so thrilled, he said he wanted to be buried in it. I had never heard that one before!
Click on the image to open
2 coats of primer, 2 coats of paint, except on the insides of the apron and under the shelf where it was not worth wasting the paint.
Click on the image to open
1/2 maple ply with butt joints reinforced with 1 inch pocket hole screws. A dado on the bottom received 1/4 maple ply.
Allowing them to acclimate to my shop after planing some of the thickness away, but before reaching finished thickness.
Click on the image to open
But wait... there is more!
The space between the slide mounts was perfect for a secret compartment. It is about 12 inches wide, 18 inches long, and 1 3/4 inches deep. Perfect for a pistol or cash or... whatever. This was a surprise for the customer - he was so excited about it!
Click on the image to open
Click on the image to open
Click on the image to open
Have something to say? Share your thoughts with us in the comments below.