Photo By Scott Wunder
Believe it or not, until recently I had never done any turnings. I have been messing with wood for a solid twenty years and never once have I even turned on a lathe. I’ve seen Norm do it a bazillion times on “The New Yankee Workshop” and listened to plenty of other woodworkers tell me about their turning escapades, but I never felt inclined to do it myself. I guess it’s because I am not attracted to work that has turnings in it, so they rarely end up in pieces that I am building and if they do, I pay someone else to do them.
It wasn’t by my choosing, but I did agree to build a bench with multiple turnings after my customer changed her mind on what she wanted. She showed me a picture from Sawkille.com of their “Tall Rabbit” bench and asked if I could make one like it for her with a variation on the length. Since I already had her deposit on the previous project, I didn’t want to say no and send back the money, so I said yes. I looked at it this way, if I consider myself a real woodworker and I am interested in spreading real-world useable woodworking knowledge, then it can’t hurt for me to have more knowledge myself. After all, was it possible that I would consider myself a real woodworker and die one day never having done a single turning? Sounded pretty hypocritical to me.
First off, let me say that the work from the kids at Sawkille is very nice, and though I don’t know them from Adam, I do appreciate the attention to design details that show in their work. I spent a lot of time messing with small details and proportions, and there is no doubt in my mind that they have spent exponentially more time on those same details and slight variations than I did.
This “Tall Rabbit” bench from Sawkille.com is what started my career as a woodturner.
The picture above is in black, but my customer saw some other variations and decided to go with bleached maple, and though it didn’t seem necessary on maple, bleaching gave the wood a very different look. The maple went from a light yellow-white to bone white with a couple of applications of two-part wood bleach. That part was as simple as could be – the actual turning was not.
Actually, I take that back. The short turnings weren’t too bad. After I turned the first couple and started to get a feel for it, the next 17 went pretty fast and came out nice. I got my time down to about 15 minutes each, which didn’t set any speed records, but it was a pace I could live with. If I did them all at that rate, I could turn all of the pieces in about 6 or 7 hours, which sounded like a fine day of work.
As you might have imagined, I wouldn’t have much to talk about if it all went down like that.
My troubles started when I stepped up to the legs and long stretchers. All of those are in the 24″ range, and about three times as long as the easy-peasy pieces. Out near the ends, where everything is solid, the work went according to plan, but in the middle, I would simply say that it did NOT. No matter how I attacked the middle, whether it be with a light touch or a hard push or maybe a quick jab or a different angle or a different speed or perhaps standing on a different foot or even just squinting a bit more, nothing improved. The piece of maple just jumped and kicked like a bucking bull, and I couldn’t stop it.
Even though I knew my problems were the result of the longer pieces, I imagined that a better turner (or at least someone who had turned at least once before in their life) could overcome the bounciness with better technique. I kept trying different lathe tools and worked slowly to get the pieces as good as possible, and while the overall shape was acceptable, the surface was not. It was nubby, like off-road truck tires, and there were plenty of spots were the wood was just ripped instead of cut. To finish up, I finally dumped the lathe tools and grabbed the sandpaper. I decided to take full advantage of the easy sanding on the lathe and let the paper do the work. Of course, it took awhile, but it was the only way I could come up with to overcome the bouncing spindle syndrome.
After I had a few of the long turnings done, I talked/complained to random shop patrons about my lathe fun and one of them mentioned using a rasp. Apparently, he had more turning knowledge than me (I think everyone does), and he had used the rasp a lot. It made good sense – a rasp is really just super-aggressive sandpaper. Plus, by holding the rasp more parallel to the piece than perpendicular, the rigid flat shape worked great to form the gradual curves with no humps. It wouldn’t have worked so well on intricate turnings, but it worked great in this case.
After finishing this project, I have a new respect for wood turners and turning. After all, my turnings were simple and still provided quite the challenge. When I think about some of the turnings I have seen, especially in other works, like large hollow vessels, and I consider all of the issues that the turner might face in a project like that, it really makes me appreciate the craft of it. And, though I may never do another turned project in my life, I am glad I gave this one a go.
Have something to say? Share your thoughts with us in the comments below.