Building a Mahogany and Wenge Table: Step by Step
Click on the image to open
My client commissioned an entry console table that features swoopy, sculptured legs and two curvy drawers for small items like keys and such.
Click on the image to open
You've seen what went into this piece, so now here's how it came out. My thanks to Paul Schraub Photography for the studio beauty shots.
Click on the image to open
Because the pivot point for the drawer is close to the center line of the table, about half of the main compartment is somewhat inaccessible, so I fitted a small sliding inner container to fill that space.
Click on the image to open
To pivot the drawer, there's a small finger-pull carved into the end of each drawer.
Click on the image to open
The concept drawing. Complex legs like these start with a paper pattern printed full-scale from the computer model.
Click on the image to open
A paper pattern printed full-scale from the computer model. The patterns are placed on the plywood template material such that the mating edges of the parts line up with the straight-and-square milled plywood edges.
Click on the image to open
Once rough milled on the bandsaw, they are smoothed and faired by hand with rasps and sandpaper.
Click on the image to open
Once rough milled, again on the bandsaw, the mating edges are trimmed straight using a straight-edge saw guide.
Click on the image to open
After the mating faces are established, dadoes are cut across them to form bridle joints.
Click on the image to open
The next step is to trim them to exactly match the templates using the router table. In a design like this, with highly curved parts that meet at variable angles its important to leave flat ears to act as clamping aids.
Click on the image to open
The next step is to mill and attach the contrasting feet. To create a pleasing look, its important to maintain a continuous grain flow from leg to foot. With legs that are square in cross-section, structural integrity can be maintained by creating the foot by just veneering the bottom of the leg. But with curved legs that are rounded in cross-section its much easier to simply attach a solid foot to the leg that can be shaped and smoothed with impunity. Because the joint between feet and legs in this situation is, by necessity, an end-grain to end-grain joint, it has very little structural integrity. Therefore I always support this type of joint with a mechanical fastener, aka, a screw. Once the pre-drilled foot is glued in place, a pilot hole is drilled into the leg and the screw inserted.
Click on the image to open
With curved legs that are rounded in cross-section its much easier to simply attach a solid foot to the leg that can be shaped and smoothed with impunity. Because the joint between feet and legs in this situation is, by necessity, an end-grain to end-grain joint, it has very little structural integrity. Therefore I always support this type of joint with a mechanical fastener, aka, a screw. Once the pre-drilled foot is glued in place, a pilot hole is drilled into the leg and the screw inserted.
Click on the image to open
Once the foot is attached, the leg can be tapered and rounded. Because the tapered legs change in thickness along their length, the radius of the edges has to change, as well. To make this easier, I use several round-over router bits of increasing radius as I move up the leg. This makes creating a consistently changing edge profile a snap.
Click on the image to open
Here are the four back leg pieces dry fit together. You can see the floating bridle tenon that connects all four pieces, as well as the positions of the clamping ears at critical points.
Click on the image to open
Then its just a matter of gluing it all up.
Click on the image to open
After the back leg sub-assembly has dried, the clamping ears are removed and the final fairing completed.
Click on the image to open
Et voilá, the assembled base.
Click on the image to open
Click on the image to open
Here it is in its location.

My client had recently renovated her waterfront apartment in San Francisco and was looking for a unique entry table to act as both a repository for keys and other small items upon arrival, as well as a statement piece on which to display flowers, and such, alongside their impressive art collection.

The footprint was constrained by the narrow dimensions of the entryway. My solution was an elliptical demilune table with two pivoting drawers. The top shape has an appropriately nautical feel, and provides the needed surface area without presenting any unfriendly sharp corners to passers by.

The under-structure of the table is highly sculptural, with a Kagan-esque feel. The two drawers pivot on ball bearings for a smooth action, and feature recesses for small items, as well as a sliding, removable inner tray that maximizes storage capacity.

 


Michael Singer operates Michael Singer Fine Woodworking, Felton, CA. This project was entered in the Custom Woodworking Business Design Portfolio competition for 2012.

 

Have something to say? Share your thoughts with us in the comments below.